London, Brighton & South Coast classes B2, B2s and B3
The London, Brighton & South Coast Railway had relatively light express trains on the London to Portsmouth line, which were still pulled by Singles in the early 1890s. Since these had reached their limits, Robert Billinton developed the first LB&SCR locomotives with a leading bogie. Between 1895 and 1898 25 were built in Brighton, designated class B2.
The nickname “Grasshopper” is probably a reference to unsteady running characteristics. Since their power was described as too low for their tasks, Billinton had the B3 “Bessemer” built in 1897 with a larger boiler. There were initially no modifications to the existing locomotives und also the ones built until 1898 got the original boiler.
It was only Marsh who had all B2 and B3 rebuilt from 1906 onwards with the same boiler as the class C3 freight locomotives, which became class B2x. This boiler was heavier, but had a smaller heating surface and still achieved greater output. The B2x was phased out with the electrification of the line to Portsmouth between 1929 and 1933.
Technical data
General
| Property | B2 | rebuilt B2x | B3 |
|---|---|---|---|
| Built | 1895-1898 | 1907-1916 | 1897 |
| Manufacturers | Brighton | ||
| Wheel arrangement | 4-4-0 (American) | ||
| Gauge | 1,435 mm (Standard gauge) | ||
Dimensions and weights
| Property | B2 | rebuilt B2x | B3 |
|---|---|---|---|
| Wheelbase | 5.35 m | ||
| Service mass | 43.5 t | 47.6 t | 45.4 t |
| Adhesion mass | 29.3 t | 31.3 t | 31 t |
| Total mass | 70.6 t | 74.7 t | 72.5 t |
| Rigid wheelbase | 2.67 m | ||
| Axle load | 15.6 t | 17.1 t | 7.2 t |
| Water capacity | 11,818 l | ||
| Fuel capacity | 4.1 t (coal) | ||
Boiler
| Property | B2 | rebuilt B2x | B3 |
|---|---|---|---|
| Grate area | 1.74 m² | 1.732 m² | 1.914 m² |
| Firebox surface | 10.66 m² | 9.408 m² | 10.252 m² |
| Tube heating surface | 114.016 m² | 109.972 m² | 125.387 m² |
| Evaporative heating surface | 124.676 m² | 119.381 m² | 135.639 m² |
| Total heating surface | 124.7 m² | 119.4 m² | 135.6 m² |
Power plant
| Property | B2 | rebuilt B2x | B3 |
|---|---|---|---|
| Driver diameter | 2,057 mm | ||
| Boiler pressure | 11.7 bar | ||
| Expansion type | simple expansion | ||
| Cylinders | two, 457 x 660 mm | ||
Power
| Property | B2 | rebuilt B2x | B3 |
|---|---|---|---|
| Power source | steam | ||
| Estimated power | 485 kW (659 PS) | 503 kW (684 PS) | 541 kW (736 PS) |
| Starting effort | 66.8 kN | ||
Calculated values
| Property | B2 | rebuilt B2x | B3 |
|---|---|---|---|
| Factor of adhesion | 1 : 4.29 | 1 : 4.59 | 1 : 4.55 |
| Optimal speed | 45 km/h | 47 km/h | 50 km/h |
| Power-to-weight ratio | 11.2 kW/t | 10.6 kW/t | 11.9 kW/t |
| Heating Surface Equivalent | 178.0 m² | 166.4 m² | 186.9 m² |
| Cylinder volume/HSE | 1 : 1,218.37 | 1 : 1,302.97 | 1 : 1,160.20 |
| Adhesive weight/Total | 1 : 1.49 | 1 : 1.52 | 1 : 1.47 |
| Tractive force/Heating surface | 1 : 11.20 | 1 : 11.69 | 1 : 10.29 |
| Grate area/Heating surface | 1 : 71.65 | 1 : 68.93 | 1 : 70.87 |
| Firebox/Tube surface | 1 : 10.70 | 1 : 11.69 | 1 : 12.23 |