Banner
Navigation
loco-info.com
The reference for locomotives and railcars

Lower Austrian State Railways Mh and Mv

Austrian Federal Railways classes 299 and 399

Austria 1906 8 produced
Works photo of Mh.3 Carl Pflanz PD

The Mariazellerbahn ordered the Mh in 1906 to get more powerful locomotives with larger supplies for their new mountain section. The design was influenced by the Bosnian IVa5, but got a superheater and cylinders with simple expansion. Four driving axles ensured enough adhesion. To create enough flexibility for curves with a radius of 80 meters, it got a Krauss supporting tender. This steered the last driving axle in curves, leading to a rigid wheelbase of only two meters.

The first four Mh were built by Krauss at Linz in 1906. In the following year, two Mv were built to compare the superheated simples with saturated compounds. These had the same firebox, but a larger tube heating surface instead of the superheater. The piston valves of the Mh had been replaced by slide valves in the Mv. As the Mh was more successful, two more were built in 1908. This was able to haul 120 tonnes on the long 2.3 percent incline of the Mariazellerbahn with 30 km/h.

Their service on the Mariazellerbahn was very short due to the electrification that was completed in 1911. Five Mh were used in Bosnia during World War I. After the war, the Mh and Mv found work on other narrow gauge lines in Austria. While they had been assigned Reichsbahn class 99 during World War II, the Mh became ÖBB class 399 in 1953 and the Mv became class 299. The two Mv were already withdrawn in 1973 and rebuilt into snow plows. The Mh was used regularly by the Waldviertler Schmalspurbahnen until the eighties and hauled some trains until 2001. All six Mh are sill existing, of which three are currently in working condition.

Technical data

General

Property Mh Mv
Built 1906-1908 1907
Manufacturers Krauss Linz
Wheel arrangement 0-8-4T (Engerth)
Gauge 760 mm (Bosnian gauge)

Dimensions and weights

Property Mh Mv
Length 11.66 m
Wheelbase 8.10 m
Rigid wheelbase 2.00 m
Empty weight 35.6 t 34 t
Service weight 45.1 t
Adhesive weight 30 t
Axle load 7.5 t
Water capacity 5,000 l
Fuel capacity 1.9 t (coal)

Boiler

Property Mh Mv
Grate area 1.6 m²
Firebox surface 6.52 m²
Tube heating surface 80.26 m² 98.26 m²
Evaporative heating surface 86.78 m² 104.78 m²
Superheater surface 18.34 m²
Total heating surface 105.1 m² 104.8 m²

Power plant

Property Mh Mv
Driver diameter 900 mm
Boiler pressure 13 bar
Expansion type simple expansion compound
Cylinders two, 410 x 450 mm two, HP: 370 x 450 mm and LP: 550 x 450 mm

Power

Property Mh Mv
Power source steam
Estimated power 400 kW (544 PS) 340 kW (462 PS)
Top speed 35 km/h
Starting effort 92.9 kN 52.1 kN
Starting effort simple 62.5 kN

Calculated values

Property Mh Mv
Factor of adhesion 1 : 3.17 1 : 4.71
Optimal speed 26 km/h 40 km/h
Power-to-weight ratio 8.9 kW/t 7.5 kW/t
Heating Surface Equivalent 156.1 m² 137.4 m²
Cylinder volume/HSE 1 : 761.39 1 : 741.31
Adhesive weight/Total 1 : 1.50
Tractive force/Heating surface 1 : 18.45 1 : 12.45
Grate area/Heating surface 1 : 65.70 1 : 65.49
Firebox/Tube surface 1 : 12.31 1 : 15.07
Total/Superheater 1 : 4.73
Auf Deutsch umschalten

Settings

Your settings are retained for this browser session only.

Consent to cookies

We use cookies to save your display settings. If you decline, the settings are retained only for the current browser session.