loco-info.com
The reference for locomotives and railcars
Navigation
Random
Search
Compare
Settings
Prussian S 9 Altona 561 and 562
Germany | 1904
2 produced
Altona 561, the streamlined vehicle
Altona 561, the streamlined vehicle
works photo Henschel

In search of a very fast steam locomotive for lighter trains, railway inspector Gustav Wittfeld developed the S 9 with the 4-4-4 wheel arrangement, which should not be confused with the S 9 that was mass-produced a few years later. The tender from the Association of German Engineers called for a machine that should be able to pull a 120-tonne train at at least 120 and if possible 150 km/h. The special thing about the two test locomotives was that they had an additional front driver's cab, which was intended for better observation of the route. The engine driver talked to the second driver via voice connection, who was in the rear cab in the usual position together with the fireman. Since the symmetrical wheel arrangement also allowed high reverse speeds, there was also a driver's cab at the end of the tender.

The first vehicle was provided with casing that was wedge-shaped at the front and from which it was hoped that a power saving of 250 to 300 hp would be achieved. There were a few windows in the side walls on both sides of the boiler so that this room could be used as a connecting passage. The tender also had an aisle and allowed to walk into the train. The second locomotive did not have the casing, but also had a wedge-shaped front on the front cab. The saturated engine was one of the few in Germany with three cylinders and compound steam expansion. The center cylinder took on the live steam and the two outer ones served as low-pressure cylinders. While the high-pressure cylinders of locomotives with two and four cylinders have a significantly smaller diameter, all three had the same dimensions here.

During the tests with the first locomotive, one quickly came to the realization that the expectations could not be met. The locomotive had about 1,400 hp, with which the 109-tonne train with three cars could be accelerated to 128 to 137 km/h on different runs. With a train that was twice as long and weighing 224 tonnes, it took more than ten minutes to reach the 110 km/h mark and the maximum speed was 118 km/h.

Later state after the rebuilding
Later state after the rebuilding
Locomotive Magazine, August 1934

Since these achievements were not in proportion to the very complex construction, there was no series production. As a result, not only was the casing of the first engine removed, but the front cabs were also removed and the locomotives used like conventional steam locomotives. In addition, an adjustment of the offset between the cylinders was necessary, since at certain speeds there had been very strong shaking movements. A very similar construction, designed at the same time by Henschel, was a tank locomotive with the designation T 16. It had the wheel arrangement 4-6-4T and was intended for uphill stretches in Thuringia. Since it had an axle load of 20 tonnes, it could not be used on most routes and was returned to the manufacturer after a short time. The two S 9 were only used until 1918 and then scrapped.

General
Built1904
ManufacturerHenschel
Axle config4-4-4 (Reading) 
Gauge4 ft 8 1/2 in (Standard gauge)
Dimensions and Weights
Length81 ft 5 3/16 in
Length loco480 ft 7 11/16 in
Wheelbase40 ft 8 3/16 in
Rigid wheelbase8 ft 4 13/16 in
Empty weight174,165 lbs
Service weight197,313 lbs
Adhesive weight80,689 lbs
Axle load37,479 lbs
Water capacity4,385 us gal
Fuel capacity15,432 lbs (coal)
Boiler
Grate area47.3 sq ft
Firebox area164 sq ft
Tube heating area2,632 sq ft
Evaporative heating area2,796 sq ft
Total heating area2,796 sq ft
Power Plant
Driver diameter86.6 in
Boiler pressure203 psi
Expansion typecompound
Cylindersthree, HP: 20 5/8 x 24 13/16 in
and LP: 20 5/8 x 24 13/16 in
Power
Power sourcesteam
Indicated power1,408 hp (1,050 kW)
Optimal speed43 mph
Top speed85 mph
Starting effort21,040 lbf
with start valve25,248 lbf
Calculated Values
steam locomotive
express
streamline
prototype
cab forward
last changed: 01/2022
loading...

We use cookies to save the following settings:

  • selected navigation structure
  • selected language
  • preferred units
  • spelling of railway company names

If you refuse the use of cookies, the settings will only be retained for the current session and will be reset to the default values the next time you visit the site.

Display of units

Here you can set the desired unit system for the technical data.

  • Metric: Lengths in meters, weights in tonnes, and volumes in cubic meters
  • Imperial (UK): Lengths in feet/inches, weights in long tons and volumes in imperial gallons
  • Imperial (US): Lengths in feet/inches, weights in pounds, and volumes in US gallons
  • Individual: Depends on the country of origin of each locomotive
Operator names

Here you can set the display of railway company names.

  • Short: Abbreviation or short form of the name
  • Standard: commonly used name, partially translated to English
  • Complete: full name in local language